Exactly How to Install a Bath Tub in Your Bathroom
Exactly How to Install a Bath Tub in Your Bathroom
Blog Article
Have you been looking for resources concerning A Step-by-Step Guide to Installing a Bathtub?
Installing a bathtub isn't exactly brain surgery, however it does call for strong plumbing, woodworking, and often, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably hard project. If the old tub is easily accessible, the job can relocate easily; if you have to open up a wall surface to eliminate the old bathtub and also place the new bathtub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will need a helper to vacate the old tub and set in the new one. Ensure you have actually qualified yourself for the task as well as fit trying it. As opposed to working with a service provider to take control of a halfway-completed project, it is better to take into consideration using one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This article will help you install a brand-new bath tub in your bathroom if you have actually currently acquired a brand-new bathtub and also do not need to change the arrangement of your previous supply of water pipes.
Your tools and also product list must make up the following:
Preparing for the Installation
To start with, the sustaining framework provided with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be suited its final setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is disconnect the water. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited access that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel all set for the remaining water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Utilizing both wooden boards under its feet, position the bathtub in the required position. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small factors.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the tub up until the level reviews degree.
To mount taps, fit the bottom of the furthest adaptable faucet connector to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Switch on the supply of water as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and also the normal electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub must wait up until the tub has actually been utilized a minimum of once as this will settle it right into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap as well as the sink. Protect the faucet in place with the maker given backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical tap ports. The previous type ought to be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to break an inflexible seal, creating the water to penetrate the wall surface between the bath as well as the tiling, bring about complications with dampness as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes as well as cartridges, and also can securing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in use. The sealant can split relatively early if you do not take into consideration this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily offered on the marketplace. It is advisable to fit the tiles utilizing waterproof or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our article about Installing A Bathtub. Thanks a lot for taking a few minutes to browse our blog post. Enjoyed reading our entry? Please share it. Help somebody else discover it. I value reading our article about How to Install a Bathtub Yourself.
More Details Report this page